FLOOD BARRIER H80
SPECIFICATIONS
Prod. No. H80
Material:

Sea-water-resistant 3.0 mm marine-grade aluminium, EN-AW-5754 H22.
Foot beam in 1.5 mm steel Magnelis.

Dimensions:

1010 x 890 mm. Plus a 100 mm lip on one short side and one long side.

Weight:

Barrier section 8.4 kg (support leg 1 kg + foot beam 1.7 kg)

PRODUCT DESCRIPTION

 

Inero’s patented flood barrier in its lowest version, designed to withstand water levels up to 80 cm. A sturdy, durable barrier with quick connectors for easy, time-saving installation.

INERO™ flood barrier segments and support legs are made of sea-water-resistant marine-grade aluminium. The material has high durability and withstands extremely tough outdoor conditions. The sections are erected using a sturdy aluminium support leg with a foot beam, in Magnelis steel plate. The sections interlock using a patented quick connector to form a continuous, flexible barrier that adapts to the substrate. INERO™ flood barriers are suitable for all common substrates, such as grass, gravel and asphalt. They can also be curved through the use of corner sections – outer and inner corners of 30°. The barriers stop and withstand both standing and rushing water and can be assembled directly in the water as long as the water level is no more than 30 cm.

ASSEMBLES IN THREE EASY STEPS

INERO™ flood barriers are easy to assemble, with no previous knowledge. Two to three persons can install 100 metres of H80 barrier in about an hour.

  1. Connect the barrier sections with the quick connector. It is easiest to do so from left to right.

  2. Mount the support leg and the foot beam. The two galvanized (M12) screws and pre-mounted nuts fit into keyhole slots on the long side of the barrier. Adjust by hand or using a tool.

  3. Roll the specially designed polyethylene film over the barrier framework, attach with clips on the top edge, anchor at the bottom with sand, gravel or heavy chains.

LOGISTICS

Lightweight materials and innovative design contribute to a low weight and good stackability, which simplifies storage and transport. One galvanized steel pallet holds 100 metres of complete barrier (barrier sections, support legs, foot beams and membrane). One steel pallet of 100 meters of barrier weights approx. 1500 kg. Measurements: 1500 mm x 1000 mm x 1100 mm. A cargo container can hold 700 metres.

After use, simply clean the barrier and reload onto the pallets.

ENVIRONMENT

INERO™ flood barriers are designed with minimal materials. Their low weight also means reduced carbon emissions from transport. The barriers have an extremely long service life and are 100% recyclable. The polyethylene film is single-use only and is suitable for eco-friendly incineration.

INERO™ flood barriers are also available in 100 cm, 150 cm and 170 cm height. The size of the quick connector is the same regardless of height, which means that different barriers can be interconnected.

OUR FLOOD CONTROL CANADA TEAM

Our team with deep industry understanding:

  • Laura Card, P. Geo. 

       Vancouver Island, BC

  • Mike Walsh, P. Eng.

       Kelowna, BC

  • Dirk Stroda, CEO

       Customer Service, Logistics,

       Business Development

  • Aaron Stroda B.ASc. 

       Mechanical Engineer 

 

CONTACT US
FOR OUR EXPERT ADVISE

HEAD OFFICE CANADA

Dirk Stroda  I  CEO  I  Director of Business Development

FloodControlCanada 

VORTEX Management & Consulting Ltd.  

394 Stellar Drive

Kelowna BC V1W 4K4

Tel 1.800.756.8027

Fax 1.888.357.2763

 

email: info@floodcontrolcanada.com

  • LinkedIn Social Icon
  • Facebook Social Icon

© 2019 VORTEX Management & Consulting Ltd. Kelowna BC Canada